Cavities and compressed plasma
An optical cavity changes the environment beside an electronic junction; a contracting lithium liner compresses magnetized plasma. Inspect both apparatuses in 3D and compare their measured current and temperatures.
Interactive apparatus
- Reflector
- Optical cavity
- Upper metal
- Insulator
- Lower metal
- Collection circuit
Cavity and junction
The optical cavity sits above a metal–insulator–metal junction, changing the electromagnetic environment beside it.
Layer separation changes the view only; it does not calculate device output.
Electrical load point
Where between short circuit and open circuit does the load receive the most power?
Current: 80% of short-circuit current. Model load power: 0.896 pW.
Normalized straight-line I–V teaching model, using the paper’s Figure 4 maximum of 1.4 pW. The 33 nm example and the paper’s 107 nm array tests are different datasets.
A cavity beside a junction
Moddel and colleagues report electrical current from a metal–insulator–metal junction with an optical cavity on one side and no applied voltage. The experiment links cavity thickness to the current–voltage response. Its companion paper examines conductance: how readily current changes when voltage changes.
The authors propose that the cavity’s optical modes affect the capture of excited electrons. The open questions concern the asymmetry, which carriers reach the terminals, and how materials and geometry change the response.
- Smallest cavity in the reported series
- 33 nm
- Maximum power calculated from the I–V line
- 1.4 pW
The active junction overlap is 0.02 μm², smaller than a complete packaged device. Figure 4, the array measurements and eight control series describe different parts of the experiment.
Heat by compressing the field
The October 2026 LM26 papers describe a magnetized plasma compressed inside an imploding lithium liner. During compression, the experiment measures magnetic flux, temperature and neutron production.
- Filtered X-rays: peak electron temperature
- 1180 ± 65 eV
- Thomson scattering: electron temperature
- 1090 ± 40 eV
- Neutron yield: inferred ion temperature
- 459 ± 33 eV
The observations sample different species and moments in the same shot: the X-ray peak occurs at radial compression 2.75, after the Thomson observation at 2.35.
The ion-temperature interval covers counting statistics at 90% confidence. Fuel dilution, density and plasma-volume assumptions add separate uncertainties; the three error bars describe different measurements.
Original papers
2021
Optical-Cavity-Induced Current
Garret Moddel, Ayendra Weerakkody, David Doroski and Dylan Bartusiak. Symmetry 13, 517 · 10.3390/sym13030517.
Electrical current, current–voltage curves, cavity thickness, eight control series and a 4 × 4 array.
2021
Casimir-cavity-induced conductance changes
Garret Moddel, Ayendra Weerakkody, David Doroski and Dylan Bartusiak. Physical Review Research 3, L022007.
A companion experiment examining how the junction conductance changes with its cavity.
8 October 2026
Compressional heating above 1 keV on the LM26 magnetized target fusion machine
S. J. Howard and colleagues. arXiv:2610.11890v1.
Magnetic-flux compression, electron heating, ion-temperature inference and neutron production in LM26.
8 October 2026
Thomson Scattering Measurement of 1 keV Electron Temperature on Lawson Machine 26
P. Carle and colleagues. arXiv:2610.11769v1.
The optical diagnostic, its spatial and temporal sampling, and the measured electron temperature.
2023
The SPARC Toroidal Field Model Coil Program
Zachary S. Hartwig and colleagues. arXiv:2308.12301.
A large-scale REBCO superconducting magnet reaching 20.1 T peak field on the conductor.
2012
Test of zero-point energy emission from gases flowing through Casimir cavities
Olga Dmitriyeva and Garret Moddel. Physics Procedia 38, 8–17 · 10.1016/j.phpro.2012.08.007.
The earlier gas-flow experiment: infrared measurements, gas/coating comparisons and the chamber’s radiation balance.